What's new
By:
Pinball info

Register a free account today to become a member! Once signed in, you'll be able to participate on this site by adding your own topics and posts, as well as connect with other members through your own private inbox!

In Progress Whitewater Full Refurb

Bank holiday weekend progress.
Added some of the powder coated bits to the cabinet, waiting on some double sided tape to arrive before putting the side rails on.
Nearly time for head to meet body again! :)
13115663_10156855552160472_1832290661_n.jpg
13020366_10156817278230472_2039396277_n.jpg
 
Playfield; good and bad.
Added all of the new plastics which look a lot better than the old ones!
13162395_10156870306180472_1925486595_n.jpg
13152801_10156870306225472_57161137_n.jpg
The 'missing plastic' bought from a chap on pinside looks a lot better than the standard metal :thumbs:
13152632_10156870306615472_234076271_n.jpg
Boulders added with cliffy protectors and blue flasher domes.
13115384_10156870306330472_1290554773_n.jpg
13140736_10156870306305472_1626044637_n.jpg
13140856_10156870306370472_1719278336_n.jpg
Then it was time to add some ramps. Old and new below :eek:
13149825_10156870306425472_777180467_n.jpg
Unfortunately this is where I ran into a problem. The RH metal ramp protector was missing and is unfortunately unobtanium as far as I know (??) but luckily I had a spare spine chiller protector which I'm going to attempt to adapt.
13162409_10156870306545472_1492342540_n.jpg
13152864_10156870306585472_1744786601_n.jpg
I'm a bit stuck until this is sorted but I did test fit the disaster drop ramp along with the mini playfield to make sure everything was lining up.
13152891_10156870306460472_1643137221_n.jpg
It'll need a bit of gentle persuasion but will should be fine. Also test fitted the spine chiller ramp and that was the weekends progress.
13162526_10156870306525472_1062600095_n.jpg
Cheers all :)
 
Beautiful. Did you get a full ramp set perchance?? I'm still after a better ramp which sits over the top of the whirlpool
 
Thanks mate :)
I did but all of the existing ramps are fooked unfortunately. I'll take a picture tonight but I'd say there's almost no way it's in better condition than the one you have.
 
Ah that's a different ramp to the one I was thinking. Mine might be in better condition actually, I'll have a look tonight.
 
looking good.
Change out that red lens by the whirlpool tho!
Its impossible to get at without taking all the ramps out afair
 
I was thinking of leaving it red for danger. Seeing how much of a mission it is to get to you might be on to something though...
I'll have a look tonight.
 
Its the only one I want to change on mine,
got the cover and tried to change it but it was too much of an ordeal.
Its on the todo list.........
 
I know that it's not a competition but I'm pretty sure this is in a worse state than yours @Spandangler :eek:
13115889_10156874236480472_2124220979_n.jpg
Apologies for getting your hopes up :(
This is the one I thought you meant which is also completely destroyed.
13162495_10156874236450472_1420458923_n.jpg
On a plus note I had the grinder out and managed to cut the ramp protector down to the right size so the the rebuild can continue. :thumbs:
13162311_10156874236380472_128166360_n.jpg
 
That's fine mate. Thanks for looking.
If you happen across one in the future, grab it and I'll take it off you.
 
Not too much progress recently on account of getting married last weekend :)
Realised that the boulder decals either side of the ramps weren't included with the new ramp set so had to order them from Ministry of Pinball which took 4 weeks!!
I couldn't fit the ramps until they arrived so the playfield has been pretty much parked.
13474091_10157035213275472_1166488144_n.jpg
Once they arrived everything went together pretty quick but what a mission fitting these ramps are! :cuckoo:
13454035_10157035213290472_15275629_n.jpg
13457605_10157035213305472_688956233_n.jpg
New Light Whirlpool plastic looks a lot better than the last one which wouldn't shine up no matter how much I tried.
13474091_10157035213360472_614900261_n.jpg
13479316_10157035213410472_394735194_n.jpg
13472213_10157035213440472_809736998_n.jpg
Getting there with the cabinet also so hoping to get the playfield back in there this weekend! :)
13479695_10157035213260472_1570690637_n.jpg
13473839_10157035212900472_2132219875_n.jpg
Cheers :thumbs:
 
Just thinking the clearcoat bubbling - after sanding do you wipe over with some turps or similar to degrease ?

I always did just to make sure

Cheers Kev
 
newdos said:
Just thinking the clearcoat bubbling - after sanding do you wipe over with some turps or similar to degrease ?

I always did just to make sure

Cheers Kev
Click to expand...
Cheers Kev :)
Yeah I reckon that's probably what happened, missed a step out in the prep and it bit me! :mad:
 
First weekend I've had free in a while so wanted to get cracking and get this thing done.
Head finally meets body and it fits! Don't know what I was worrying about. :rolleyes:
14249139_10157392262360472_1209453469_n.jpg
14249017_10157392262215472_816888471_n.jpg
Next thing was to get the playfield in and hooked up and again amazingly everything fits! :clap:
14256424_10157392262420472_1346503455_n.jpg
Crossed everything, turned it on and this is where the smiles stop. :(
On the plus side nothing started smoking and no fuses popped but nothing. The led's on the boards light up, the speakers hum but no DMD or boot up.
14218368_10157392262545472_853458609_n.jpg
Two inserts on the playfield are lit for some strange reason...
14194230_10157392262600472_2029650927_n.jpg
HELP PLEASE!! :eek:
 
The first thing I would check is that the ribbon cables are all sitting on the correct pins and the right way around. Convention states that the red banded side should be connected to pin 1, which should be labelled on the boards too. Its very easy to get things 1 pin out of line etc.
 
aaronhicksuk said:
The first thing I would check is that the ribbon cables are all sitting on the correct pins and the right way around. Convention states that the red banded side should be connected to pin 1, which should be labelled on the boards too. Its very easy to get things 1 pin out of line etc.
Click to expand...

Thanks for that, one was the wrong way round but it hasn't made a difference unfortunately...
 
Great work man. What an adventure. Looks like a brilliant game, although I’m not sure there are enough ramps for my taste ;) really hope I get to play one soon.


Sent from my iPhone using Tapatalk
 
You must log in or register to reply here.
Back
Top Bottom