What's new
Pinball info

Register a free account today to become a member! Once signed in, you'll be able to participate on this site by adding your own topics and posts, as well as connect with other members through your own private inbox!

In Progress Jurassic Park LE - Mod installs and Full Rubber replacement #Sparednoexpense

s000m

Site Supporter
Joined
Apr 12, 2021
Messages
599
Location
Swindon
Alias
Scott
So here's a log of the work I completed on the weekend on my newly acquired Jurassic Park LE.

Wife wanted orange so went with a full kit of Titan replacement rubbers.

@Ads Nems Never unfortunately go around to installing his Shooter rod or hooking into the power to the topper. These are truly amazing pieces of kit. I wasn't going to keep the Tilt topper but after watching it light up I seriously cannot be bothered with the official release.

Video of the Amber Rod and Topper installed and powered.



Amber Rod install:

1637454104085.jpeg

1637454122921.jpeg

1637454144431.jpeg


Rubber Kit next:

1637454179627.jpeg

Cleaned off the flippers:

1637454208456.jpeg

Slingshot removal:
Also had some @Colywobbles protectors in the coin box so installed those too:

1637454253898.jpeg


1637454277342.jpeg

1637454318971.jpeg

1637454346285.jpeg

1637454368082.jpeg


1637454380048.jpeg

Did the channels at the same time below the slings:

1637454404070.jpeg

Had to do some plastic adjustment as the ball was catching...

1637454532132.jpeg

This area was a bit of a pain...

1637454425567.jpeg

1637454471771.jpeg

Raptor area was also a PITA required a lot of removal to get the rubbers and posts in this area.

1637454454791.jpeg


1637454582160.jpeg

Posts in these area's were simple enough.

1637454605853.jpeg

The posts for a the T-REX area were a bit of a faff had to move plastic air ball protector, 'cliffy' protector and move the ramp above...

Also installed the pterodactyl mod while i was at it.

1637454696921.jpeg

The rubbers near the pop bumper area's were also a sod I had to do a lot of juggling with plastics, metal posts and ramp adjustments to get all the rubbers off. Had my wife going 'just leave it'. I honestly couldn't I wanted the whole lot as one theme....


End result:

1637454838986.jpeg

Check list:

PSU Fan replacement (fans have been ordered)
Install some simple signs near the T-REX fence.
 
OP
s000m

s000m

Site Supporter
Joined
Apr 12, 2021
Messages
599
Location
Swindon
Alias
Scott
Looking great in orange. Are you going to mod the helicopter? the stern flat plastic version is pretty bad....
Will think about it. Moneys flowing out due to the Garage conversion at the moment. Maybe once the dust has settled :D
 

kevlar

Site Supporter
Joined
Apr 11, 2013
Messages
5,580
Location
Newport, South Wales
Alias
Kevin Donovan
Oh nice! Where from?
Ebay. I can't see any on there atm except for one as part of a £60 set. It's tricky to mod, have to drill and dremmel it to accept the flipper bush that's used to hold the blades with a small bearing on the top. Worth it though if you can find one and have the patience to mod it to suit.
 

Colywobbles

Site Supporter
Joined
Nov 9, 2016
Messages
1,856
Location
Sunderland
Alias
Colin Chapman
Its no secret I never kept JP longer than a few weeks as I just didn’t get it and theme wise it’s a bit meh! for me.
That said everyone else rates it a GOAT and favourite of many here so I accept I’m weird!

So as this is a kind of modding thread can anyone help?
my question is what does the lockbar button do as I’m currently trying to design a lockdown bar plaque for it in the vein of my V2 shooter and coindoor plates.

7C8D0470-2E64-48AA-A3CC-046C7C780C85.jpeg

Sorry for the hijack scott and keep up the good work.
 
Top Bottom