The game currently has a minor fault where the stage door kick out thinks there's some times a ball in there when there isn't. The mechanism works based on optos. I did use an air can to clean them and that fixed it for about 2 weeks then it came back again. So it needs the optos replacing or checking out. But that requires a strip of the stage.
Good points:
Matt Adams completely stripped the playfield and rebuilt it. Less than 100 plays on it! I have pictures of this work.
Replacement third party ball trough opto boards as the originals are prone to failure
It is the early Pinball Magic machine - pilot? early run? It's the one in the flyer with the silver trim. I've never seen another silver trim model ever.
The CPU board has a new replacement battery backed ram
The CPU board has been refurbished as the CPU socket are sometimes an issue on these. It's got a brand new CPU socket and also a metal clasp that holds it securely.
PinballCenter.eu anti glare translite glass
Complete re-rubbered from the playfield rebuild!
Bad Points:
Rear of the backbox someone (not me) tried to sack truck it through a doorway that's too narrow so there's a bit of damage. The cabinet is in good condition otherwise.
Stage Door issue as mentioned. This will eventually stop working if it fires to many times, and you must reset it.
The backbox lock mechanism is missing
I would replace the drop targets with new ones
General Points:
It has Bally Midway legs - they are a brand new set of legs
It has pincab protectors
No broken plastics
New premium balls for working better with magnets
I put up a valuation thread and i'm looking for £2400.
I will put pictures up in the next 48 hours.
Also available to the buyer at a price to be agreed:
A whole bundle of NOS plastics and stickers
A spare CPU board (with the same refurbishments as the one in the machine)
A NOS (yes never used) Sound PCB with pinball magic roms
2 extra NOS PCBs, DMD power aux and switch matrix.
Some NOS under playfield mechanisms.
LOADS OF PIX HERE! https://1drv.ms/f/s!AuI0HQzz58f5obhZA-WyqhT7zba1pA
Thanks
Good points:
Matt Adams completely stripped the playfield and rebuilt it. Less than 100 plays on it! I have pictures of this work.
Replacement third party ball trough opto boards as the originals are prone to failure
It is the early Pinball Magic machine - pilot? early run? It's the one in the flyer with the silver trim. I've never seen another silver trim model ever.
The CPU board has a new replacement battery backed ram
The CPU board has been refurbished as the CPU socket are sometimes an issue on these. It's got a brand new CPU socket and also a metal clasp that holds it securely.
PinballCenter.eu anti glare translite glass
Complete re-rubbered from the playfield rebuild!
Bad Points:
Rear of the backbox someone (not me) tried to sack truck it through a doorway that's too narrow so there's a bit of damage. The cabinet is in good condition otherwise.
Stage Door issue as mentioned. This will eventually stop working if it fires to many times, and you must reset it.
The backbox lock mechanism is missing
I would replace the drop targets with new ones
General Points:
It has Bally Midway legs - they are a brand new set of legs
It has pincab protectors
No broken plastics
New premium balls for working better with magnets
I put up a valuation thread and i'm looking for £2400.
I will put pictures up in the next 48 hours.
Also available to the buyer at a price to be agreed:
A whole bundle of NOS plastics and stickers
A spare CPU board (with the same refurbishments as the one in the machine)
A NOS (yes never used) Sound PCB with pinball magic roms
2 extra NOS PCBs, DMD power aux and switch matrix.
Some NOS under playfield mechanisms.
LOADS OF PIX HERE! https://1drv.ms/f/s!AuI0HQzz58f5obhZA-WyqhT7zba1pA
Thanks
Last edited: