Looking for EATPM owner for project guidance

thejefu

Site Supporter
Feb 13, 2020
24
5
3
Glossop, Derbyshire
Alias
thejefu
I'm pouring over the EATPM manual and getting reading to start plugging things into things, but I figured I'd reach out to existing EATPM owners for a potential facetime/skype to do a comparison and save me some headache.

IMG_6200.jpg
 
Last edited:

Dex-Jay

Site Supporter
Nov 20, 2016
525
408
63
51
Midlands
That or upload a video with "where's 'at go? Where' this go?" and I or someone else can go through the list for you.
 
OP
thejefu

thejefu

Site Supporter
Feb 13, 2020
24
5
3
Glossop, Derbyshire
Alias
thejefu
That or upload a video with "where's 'at go? Where' this go?" and I or someone else can go through the list for you.
Since I'm going from 0, that might be a long video! About half of the connectors were marked and others were obvious, so I'm definitely about 70-80% there.

Figure I'd try the long shot and if nobody's willing to take me through their boards I'll do it the tedious way.
 

stumblor

Site Supporter
Sep 16, 2018
1,293
1,297
113
London · Davey Price
Alias
Davey Price
@thejefu The quickest way is to count the pins on the connector, and note where the key is, and then scan through the doc looking for a connector with that configuration. After that, check wire colours. You'll find it quickly enough.
 

DRD

Site Supporter
Oct 26, 2014
4,048
2,814
113
Newark
In your shoes I would get some decent quality pictures of a known working machine.

If anyone on here has an EATPM , some high res photos of the boards and connectors in the backbox could save this guy a load of time
 
OP
thejefu

thejefu

Site Supporter
Feb 13, 2020
24
5
3
Glossop, Derbyshire
Alias
thejefu
In your shoes I would get some decent quality pictures of a known working machine.

If anyone on here has an EATPM, some high res photos of the boards and connectors in the backbox could save this guy a load of time
Found the reference in the last few pages of manual, making progress!


Sent from my iPhone using Tapatalk
 
OP
thejefu

thejefu

Site Supporter
Feb 13, 2020
24
5
3
Glossop, Derbyshire
Alias
thejefu
One thing I have noticed is J1 through 3 is missing on the IC. Rest looks to be complete and in the right place.


Sent from my iPhone using Tapatalk
 

Arv

Site Supporter
Jul 21, 2011
2,326
1,264
113
Make sure those voltages are correct before you power on.

You got a picture of the apron at all?
 
OP
thejefu

thejefu

Site Supporter
Feb 13, 2020
24
5
3
Glossop, Derbyshire
Alias
thejefu
All done

IC: J1 and J3 missing
MPU: J6, J7, J8, J10, J16 missing
(All lamp/switch connectors)

Audio ribbon missing.

Gave it a boot, lit up, turned it off, doesn't want to turn on again. Guessing I'm getting these missing parts and some fuses!
 
Last edited:
  • Like
Reactions: stumblor
OP
thejefu

thejefu

Site Supporter
Feb 13, 2020
24
5
3
Glossop, Derbyshire
Alias
thejefu
I take it back, the main socket in my garage died.

We have life!...ish

Image from iOS.jpg

@Dex-Jay you wouldn't happen to shed any light on this missing connectors? They're all lamp/switch connectors so I figure it's a single cable set I'm missing?

IC: J1 and J3 missing
MPU: J6, J7, J8, J10, J16 missing
 
Last edited: